Dual Quad EFI with 2 big 4 BBL’s. FiTech EFI has made it simple with their Go EFI 2X4 625 HP self-tuning System. This kit is a bolt on for the most popular manifolds including the Edelbrock line of dual quad manifolds WITHOUT any adapters! They fit and look like they belong there because they were designed to fit from the start. Our normally aspirated kits are good thru 625 hp but our Go EFI 2X4 POWER ADDER kit can handle you guys with the bigger cubes and Roots Superchargers. One Throttle Body handles all of the brains while the second holds 4 additional injectors, and the IAC motor for idle stability. These can also be used in cross ram and tunnel ram configurations. No boost with these please! For Boosted and High HP normally aspirated applications please see our Go EFI 2X4 POWER ADDER (Part #30064). **This kit does not include linkage or fuel lines**
Bolt on 2 of these tough looking throttle bodies and drive your car as the system dials itself into the perfect calibration for all of your driving and weather conditions. If you decide you want to tune for more power or economy, the FiTech Touch Screen controller allows quick and easy on the fly adjustments at your fingertips!
The Fuel Delivery Kit includes an EFI grade 255 L/PH inline external fuel pump that is suitable for engines making up to 600 HP. (Note that some of our EFI kits are limited to less than 750 HP due to maximum usable injector sizes). This kit also includes 20-feet of EFI grade fuel hose suitable for both the inlet and return lines between the fuel tank and the engine. The kit includes two billet fuel filters. The filters include a 100 micron pre-filter and a 30 micron post filter. The hose and hose ends are push lock style for easy assembly. The hose is high pressure EFI grade.
Kit Includes:
(2) Die Cast Throttle Bodies
Handheld Controller
Windshield Mount
(8) Hi-Flow 625 HP injectors
Built-in pressure regulator
2.5 BAR Internal MAP Sensor
Throttle Position Sensor
Idle Air Control
Coolant Temp Sensor
Wide band O2 Sensor
O2 Bung Kit
-06AN Fuel Inlet Fitting
Gasket Kit
| Inline Fuel Pump |
255 L/PH External Inline Pump
EFI Pre and Post Fuel Filters
20′ of -6 Hose
5′ of -8 Hose
Fittings
Mounting Brackets
|
| Fuel Command Center |
Sump Tank Assembly w/340 L/PH Fuel Pump, Regulator and Pressure Gauge
Hose and Fittings
EFI Fuel Filter
|
| Hyperfuel G-Surge Tank |
Hyperfuel G-Surge Main Assembly |
| Hy-Fuel In-Tank Module |
Hy-Fuel Pump Main Assembly
58 PSI Fuel Regulator
Extension Shaft
Hy-Fuel Outer Ring (Red)
Hy-Fuel Inner Ring (Black)
340 L/PH Fuel Pump
(16) #10-32×1″ Flat Head Machine Screws
(8) #10-32×1.75″ Flat Head Machine Screws
(8) #10-32×1.5″ Flat Head Machine Screws
(8) #10-32 Keps Nuts and #10 Flat Washers
EFI Grade 5/16″ Hose and (2) Hose Clamps
(3) Electrical Connectors, Nuts, Washers and Rubber Boots
OEM Style Filter
1/4″ Drill Bit
O-ring
|
| Hy-Fuel Tight-Fit In-Tank Module |
Hy-Fuel Pump Main Assembly
Return Tube
Foam Gasket
Hy-Fuel C Ring (Red)
255 L/PH Fuel Pump
(6) M5-0.8x25mm Hex Head Machine Screws
(6) M5-0.8x25mm Countersunk Head Machine Screws
(6) M5-0.8 Keps Nuts
EFI Grade 5/16″ Hose and (1) Hose Clamp
(2) Electrical Connectors, Nuts, Washers and Rubber Boots
Filter Sock
(2) Cable Clamps
|
WARNING:
This product can expose you to chemicals,
which are known to the State of California to cause cancer.
For more information, visit www.P65Warnings.ca.gov.
